Assemble parts to be brazed.

组装准备铜焊的部件。

Brazing Method: Assemble parts to be brazed.

银钎焊：需钎焊件组装。

Silver Brazing Method: Assemble parts to be brazed.

银钎焊的方法：对需要进行钎焊的部件进行组装。

Vacuum brazed diamond graver is used to grave all kinds of stones.

根据客户需要，可生产各种规格各种形状的雕刻刀。

The brazed rate is an important parameter represented product quality.

钎着率是判断钎焊质量的重要指标。

When the police caught the thief in the act he tried to brazed it out.

警察当场抓获小偷作案，这个小偷却厚颜无耻，毫不在乎。

The shearing strength of the brazed joint can be also greatly strengthened.

同时还可以显著提高钎焊接头的抗剪切强度。

Local fusion deformation occurred after the product antenna combination was brazed.

某产品天线组合钎焊后，局部发生熔化变形现象。

Bending (torque) test was also performed to evaluate strength of the brazed joints.

为了评价焊接强度，还进行了抗弯强度(扭矩)测试。

The strength of soldered joint is less than a joint which is brazed, riveted or welded.

锡焊点的连接力要小于钎焊、铆接或焊接的连接点。

Sapphire and Nb alloy have been successfully brazed by use of tungsten-metallization technique.

通过对蓝宝石的钨金属化，实现了蓝宝石与铌合金的高温封接。

Grinding performance of the brazed wheel in the surface grinding of cemented carbide is studied.

以硬质合金为加工对象，研究了该砂轮的磨削性能。

So, the detection of brazed joints is very important on the theoretical and practical significance.

因此，其焊缝的检测就具有非常重要的理论和实际意义。

After cemented carbide brazed is quenched and tempered, the strength of welding stam descend obviously.

硬质合金钎焊后进行淬火、回火处理，焊缝强度明显下降。

The system brazed for 60 minutes bonded completely Fig. 5 it consists of different microstructure regions.

如果系统为60分钟保税完全(图5)，它包含不同组织的地区。

The results can provide theoretical basis for roll arrangement design of quadruple-wall curly brazed tubes.

模拟结果可为四层卷焊管配辊方案的设计提供理论依据。

In this paper, each forming operation during quadruple-wall curly brazed tubes' forming processes was summarized.

综合阐述了四层卷焊管成型过程中的各技术环节。

But the particularity and complexity of monolayer brazed diamond tools has blocked the analysis of the residual stress.

只是由于单层钎焊工具的特殊性和复杂性，有关它的残余应力的量化分析和实验测定都存在很大难度。

Radio frequency ultrasonic technique for metal brazed high-density honeycomb structures and defect recognition are described.

利用射频超声技术检测大密度金属钎焊蜂窝构件及缺陷识别技术。

The microstructure of the brazed joint was analyzed by means of a scanning electron microscope and an energy spectrum analyzer.

用扫描电镜和能谱分析仪对钎焊接头的显微组织进行了分析。

In this paper, grinding forces were measured in the grinding of granite with a high-frequency induction brazed diamond grinding wheel.

通过测量高频感应钎焊金刚石砂轮磨削花岗石过程中的磨削力，对砂轮所受的法向力和切向力进行了研究。

It analyzes the character of the current super-abrasive grinding wheel, looks into the advantages and foreground about brazed grinding wheel.

分析了超硬磨料砂轮的现状和特点，介绍了钎焊砂轮的卓越磨削性能和发展前景。

The cause of externally applied pipe load to brazed aluminum heat exchanger and the necessity of calculating allowable pipe load are analyzing.

分析了板翅式换热器封头接管外载荷产生的原因和进行许用接管载荷计算的必要性。

Spreadability, microstructures and mechanical properties of brazed joints of silver filler metals with different content of gallium were studied.

研究了不同镓含量银钎料的铺展性能、钎缝力学性能以及钎料的显微组织变化规律。

This paper discusses the effect of brazing time, brazing temperature, brazing gap and diffusion treatment on the remelt temperature of the brazed joint.

文章讨论了钎焊时间、钎焊温度、钎焊间隙及焊后扩散处理对钎焊接头再熔化温度的影响。

The brazing experiment is finished in vacuum furnace, the brazed joints with different filler metal thickness are obtained by different pressure on them.

在数控真空钎焊炉中进行钎焊试验，由于施加压力的不同，得出钎缝厚度不同的焊接试件。

It is proved in engineering that the high quality aluminum-brazed brazing alloys is the crucial technology of the bus aluminum production of window frame.

工程应用表明，高质量的铝钎料是汽车铝窗框生产的关键技术。

Choosing a appropriate thickness filler metal for brazing metal-ceramic can decrease the residual stresses in the brazed joints and improve the joint strength.

同时，选择合适厚度的钎料会降低钎焊接头的残余应力，改善接头连接强度。